请选择 进入手机版 | 继续访问电脑版

锁匠宝典

 找回密码
 立即注册
点击下载锁匠宝典安卓APPVIP购买微信号18207496235

扫一扫即可添加微信
查看: 72|回复: 0

本田摩托车 CBR929RR芯片钥匙匹配原厂资料-汽车钥匙遥控-防盗芯片匹配

[复制链接]

该用户从未签到

1万

主题

1万

帖子

4万

积分

标准版VIP

积分
40138
元宝
0
贡献
300
发表于 2021-10-18 02:17:26 | 显示全部楼层 |阅读模式
Key Registration Procedures
When the key has been lost, or additional spare key is required:
1. Obtain a new transponder key.
2. Grind the key in accordance with the shape of the original key.
3. Apply 12V battery voltage to the ignition pulse generator lines of the engine control module (ECM) using the special tool (page 20-5).
4. Turn the ignition switch ON with the original key. The immobiliser indicator comes on and it remains on.
*The code of the original key is recognised by the ECM.
*If there is any problem in the immobiliser system, the system will enter the diagnostic mode and the indicator will remain on for approx. ten seconds, then it will indicate the diagnostic code (page 20-5).
5. Disconnect the red clip of the inspection adaptor from the battery positive (+) terminal for two seconds or more, then connect it again. The indicator remains on for approx. two seconds, then it blinks four times repeatedly.
*The immobiliser system (HISS) enters the registration mode. Registrations of all key except the original key inserted in the ignition switch are cancelled. (Registration of the lost key or spare key is cancelled.)
NOTE:
The spare key must be registered again.
6. Turn the ignition switch OFF and remove the key.
7. Turn the ignition switch ON with a new key or the spare key. (Never use the key registered in previous step.) The indicator comes on for two seconds, then it blinks four times repeatedly.
*The new key or spare key is registered in the ECM.
*If there is any problem in the registration, the system will enter the diagnostic mode and the indicator will remain on for approx. ten seconds, then it will indicate the diagnostic code (page 20-6).
CAUTION:
Keep the other transponder key away from the immobiliser receiver more than 50mm (2.0 in).
8. Repeat the steps 6 and 7 when you continuously register the other new key.
NOTE:
The ECM can store up to four key codes. (The four keys can be registered.)
9. Turn the ignition switch OFF, remove the inspection adaptor and connect the ignition pulse generator connector.
10. Turn the ignition ON with the registered key.
*The immobiliser system (HISS) returns to the normal mode.
11. Check that the engine can be started using all registered key.
请英文厉害的翻译一下
[ 本帖最后由 GGYY 于 2008-6-13 20:35 编辑 ]
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则


扫一扫加客服微信

微信号18207496235

QQ|小黑屋|手机版|Archiver|锁匠宝典 ( 湘ICP备19010224号-1 )|网站地图

GMT+8, 2022-1-22 06:40 , Processed in 0.080041 second(s), 25 queries .

Powered by 汽车钥匙匹配 X3.4

© 2016-2020 锁匠宝典汽车防盗资料7×24小时查询平台

快速回复 返回顶部 返回列表